Remove more RESET keycode references (#18252)

keyboards/ai/readme.md

@@ -31,4 +31,4 @@ Enter the bootloader in 3 ways:
 
 -   **Bootmagic reset**: Hold down the key at (0,0) in the matrix (usually the top left key or Escape) and plug in the keyboard
 -   **Physical reset button**: Briefly press the button on the back of the PCB - some may have pads you must short instead
--   **Keycode in layout**: Press the key mapped to `RESET` if it is available
+-   **Keycode in layout**: Press the key mapped to `QK_BOOT` if it is available

keyboards/aidansmithdotdev/fine40/readme.md

@@ -24,4 +24,4 @@ Enter the bootloader in 3 ways:
 
 * **Bootmagic reset**: Hold down the key at (0,0) in the matrix (top left key) and plug in the keyboard
 * **Physical reset button**: Briefly press the button on the back of the PCB - some may have pads you must short instead
-* **Keycode in layout**: Press the key mapped to `RESET` if it is available
+* **Keycode in layout**: Press the key mapped to `QK_BOOT` if it is available

keyboards/at_at/660m/config.h

@@ -17,7 +17,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #pragma once
 
-/* Ensure we jump to bootloader if the RESET keycode was pressed */
+/* Ensure we jump to bootloader if the QK_BOOT keycode was pressed */
 #define EARLY_INIT_PERFORM_BOOTLOADER_JUMP TRUE
 
 /* LSE clock */

keyboards/boardrun/bizarre/readme.md

@@ -18,6 +18,6 @@ Flashing example for this keyboard:
 
     make boardrun/bizarre:default:flash
     
-The board may be reset into bootloader mode via either the reset button (on the bottom of the PCB) or a configured RESET shortcut (which may vary depending on when the PCB was flashed).
+The board may be reset into bootloader mode via either the reset button (on the bottom of the PCB) or a configured `QK_BOOT` shortcut (which may vary depending on when the PCB was flashed).
 
 See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/boardrun/classic/readme.md

@@ -18,6 +18,6 @@ Flashing example for this keyboard:
     
     make boardrun/classic:default:flash
 
-The board may be reset into bootloader mode via either the reset button (on the bottom of the PCB) or a configured RESET shortcut (which may vary depending on when the PCB was flashed).
+The board may be reset into bootloader mode via either the reset button (on the bottom of the PCB) or a configured `QK_BOOT` shortcut (which may vary depending on when the PCB was flashed).
 
 See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/cannonkeys/malicious_ergo/readme.md

@@ -13,6 +13,6 @@ Enter the bootloader in 3 ways:
 
 * **Bootmagic reset**: Hold down the key at (0,0) in the matrix (usually the top left key or Escape) and plug in the keyboard
 * **Physical reset button**: Toggle the switch on the back of the pcb to "0" and briefly press the button on the back of the PCB
-* **Keycode in layout**: Press the key mapped to `RESET` if it is available
+* **Keycode in layout**: Press the key mapped to `QK_BOOT` if it is available
 
 See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/cannonkeys/nearfield/readme.md

@@ -26,6 +26,6 @@ Enter the bootloader in 3 ways:
 
 * **Bootmagic reset**: Hold down the top left key and plug in the keyboard
 * **Physical reset button**: Briefly press the button on the back of the PCB
-* **Keycode in layout**: Press the key mapped to `RESET` if it is available
+* **Keycode in layout**: Press the key mapped to `QK_BOOT` if it is available
 
 See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/cannonkeys/satisfaction75/config.h

@@ -17,7 +17,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #pragma once
 
-/* Ensure we jump to bootloader if the RESET keycode was pressed */
+/* Ensure we jump to bootloader if the QK_BOOT keycode was pressed */
 #define EARLY_INIT_PERFORM_BOOTLOADER_JUMP TRUE
 
 /* LSE clock */

keyboards/capsunlocked/cu75/cu75.c

@@ -91,7 +91,7 @@ bool process_record_kb(uint16_t keycode, keyrecord_t* record)
     if (click_toggle && record->event.pressed){
         click(click_hz, click_time);
     }
-    if (keycode == RESET) {
+    if (keycode == QK_BOOT) {
         reset_keyboard_kb();
     } else {
     }

keyboards/carbo65/config.h

@@ -32,7 +32,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
 #define DEBOUNCE 5
 
-/* Ensure we jump to bootloader if the RESET keycode was pressed */
+/* Ensure we jump to bootloader if the QK_BOOT keycode was pressed */
 #define EARLY_INIT_PERFORM_BOOTLOADER_JUMP TRUE
 
 /* Indicator LEDs */

keyboards/clueboard/66/rev4/mine/keymap.c

@@ -1,13 +0,0 @@
-#include QMK_KEYBOARD_H
-
-/* THIS FILE WAS GENERATED!
- *
- * This file was generated by qmk json2c. You may or may not want to
- * edit it directly.
- */
-
-const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
-	[0] = LAYOUT(KC_GESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_GRV, KC_BSPC, KC_PGUP, KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, KC_PGDN, KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_NUHS, KC_ENT, KC_LSFT, KC_NUBS, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RO, KC_RSFT, KC_UP, KC_LCTL, KC_LGUI, KC_LALT, KC_MHEN, KC_SPC, KC_SPC, KC_HENK, KC_RALT, MO(1), KC_RCTL, KC_LEFT, KC_DOWN, KC_RGHT),
-	[1] = LAYOUT(KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_TRNS, KC_DEL, KC_VOLU, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_MPRV, KC_MPLY, KC_MNXT, KC_TRNS, KC_MUTE, KC_VOLD, KC_TRNS, KC_TRNS, MO(2), KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_PGUP, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, MO(1), KC_TRNS, KC_HOME, KC_PGDN, KC_END),
-	[2] = LAYOUT(BL_STEP, RGB_M_P, RGB_M_B, RGB_M_R, RGB_M_SW, RGB_M_SN, RGB_M_K, RGB_M_X, RGB_M_G, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, RGB_TOG, RGB_VAI, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, RESET, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, RGB_VAD, KC_TRNS, KC_TRNS, MO(2), KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, MO(1), KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, RGB_SAI, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, RGB_MOD, RGB_MOD, KC_TRNS, KC_TRNS, MO(1), KC_TRNS, RGB_HUD, RGB_SAD, RGB_HUI)
-};

keyboards/emery65/config.h

@@ -32,7 +32,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
 #define DEBOUNCE 5
 
-/* Ensure we jump to bootloader if the RESET keycode was pressed */
+/* Ensure we jump to bootloader if the QK_BOOT keycode was pressed */
 #define EARLY_INIT_PERFORM_BOOTLOADER_JUMP TRUE
 
 /* Indicator LEDs */

keyboards/feker/ik75/readme.md

@@ -22,4 +22,4 @@ Enter the bootloader in 3 ways:
 
 * **Bootmagic reset**: Hold down the key at (0,0) in the matrix (Esc key) and plug in the keyboard
 * **Physical reset button**: Briefly press the button on the back of the PCB
-* **Keycode in layout**: Press the key mapped to RESET if it is available
+* **Keycode in layout**: Press the key mapped to `QK_BOOT` if it is available

keyboards/fjlabs/avalon/readme.md

@@ -16,4 +16,4 @@ Enter the bootloader in 3 ways:
 
 * **Bootmagic reset**: Hold down the key at (0,0) in the matrix (usually the top left key or Escape) and plug in the keyboard
 * **Physical reset button**: Briefly press the button on the back of the PCB - some may have pads you must short instead
-* **Keycode in layout**: Press the key mapped to `RESET` if it is available
+* **Keycode in layout**: Press the key mapped to `QK_BOOT` if it is available

keyboards/foostan/cornelius/readme.md

@@ -16,6 +16,6 @@ Flashing example for this keyboard:
 
     make foostan/cornelius:default:flash
 
-The board reset into bootloader mode via either the reset button (on the back of the PCB) or a configured RESET shortcut (which may vary depending on when the PCB was flashed).
+The board reset into bootloader mode via either the reset button (on the back of the PCB) or a configured `QK_BOOT` shortcut (which may vary depending on when the PCB was flashed).
 
 See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/hand88/config.h

@@ -32,7 +32,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
 #define DEBOUNCE 5
 
-/* Ensure we jump to bootloader if the RESET keycode was pressed */
+/* Ensure we jump to bootloader if the QK_BOOT keycode was pressed */
 #define EARLY_INIT_PERFORM_BOOTLOADER_JUMP TRUE
 
 /* Indicator LEDs */

keyboards/handwired/cyberstar/config.h

@@ -32,7 +32,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
 #define DEBOUNCE 5
 
-/* Ensure we jump to bootloader if the RESET keycode was pressed */
+/* Ensure we jump to bootloader if the QK_BOOT keycode was pressed */
 #define EARLY_INIT_PERFORM_BOOTLOADER_JUMP TRUE
 
 /* RGB Light */

keyboards/handwired/dactyl/readme.md

@@ -21,7 +21,7 @@ To flash the firmware:
   - Load the .hex file into it.
 
   - Put the Teensy in firmware-loading mode:
-    * If your current layout has a RESET key, press it.
+    * If your current layout has a `QK_BOOT` key, press it.
     * If you lack a RESET key, press the reset button on the Teensy board itself.
 
   - Click the button in the Teensy app to download the firmware.
@@ -35,5 +35,5 @@ To flash with ´teensy-loader-cli´:
   - If you like, you can do both at once: `make handwired/dactyl:<keymapname>:teensy`
 
   - Put the Teensy in firmware-loading mode:
-    * If your current layout has a RESET key, press it.
+    * If your current layout has a `QK_BOOT` key, press it.
     * If you lack a RESET key, press the reset button on the Teensy board itself.

keyboards/idobao/id80/v1/readme.md

@@ -24,4 +24,4 @@ Enter the bootloader in 3 ways:
 
 * **Bootmagic reset**: Hold down the Escape key and plug in the keyboard
 * **Physical reset button**: Briefly press the button on the back of the PCB
-* **Keycode in layout**: Press the key mapped to `RESET` if it is available
+* **Keycode in layout**: Press the key mapped to `QK_BOOT` if it is available

keyboards/idobao/id80/v2/readme.md

@@ -38,4 +38,4 @@ Enter the bootloader in 3 ways:
 
 * **Bootmagic reset**: Hold down the Escape key and plug in the keyboard
 * **Physical reset button**: Briefly press the button on the back of the PCB
-* **Keycode in layout**: Press the key mapped to `RESET` if it is available *(default is [Fn]+[Esc])*
+* **Keycode in layout**: Press the key mapped to `QK_BOOT` if it is available *(default is [Fn]+[Esc])*