commit
ed6ecff292
115 changed files with 6981 additions and 1531 deletions
7
Makefile
7
Makefile
|
|
@ -198,6 +198,11 @@ ifeq ($(strip $(AUDIO_ENABLE)), yes)
|
|||
SRC += $(QUANTUM_DIR)/audio/luts.c
|
||||
endif
|
||||
|
||||
ifeq ($(strip $(UCIS_ENABLE)), yes)
|
||||
OPT_DEFS += -DUCIS_ENABLE
|
||||
UNICODE_ENABLE = yes
|
||||
endif
|
||||
|
||||
ifeq ($(strip $(UNICODE_ENABLE)), yes)
|
||||
OPT_DEFS += -DUNICODE_ENABLE
|
||||
SRC += $(QUANTUM_DIR)/process_keycode/process_unicode.c
|
||||
|
|
@ -273,4 +278,4 @@ BUILD_DATE := $(shell date +"%Y-%m-%d-%H:%M:%S")
|
|||
OPT_DEFS += -DQMK_KEYBOARD=\"$(KEYBOARD)\" -DQMK_KEYMAP=\"$(KEYMAP)\"
|
||||
|
||||
$(shell echo '#define QMK_VERSION "$(GIT_VERSION)"' > $(QUANTUM_PATH)/version.h)
|
||||
$(shell echo '#define QMK_BUILDDATE "$(BUILD_DATE)"' >> $(QUANTUM_PATH)/version.h)
|
||||
$(shell echo '#define QMK_BUILDDATE "$(BUILD_DATE)"' >> $(QUANTUM_PATH)/version.h)
|
||||
|
|
|
|||
|
|
@ -113,7 +113,7 @@ Third party libraries like LUFA, PJRC and V-USB have their own license respectiv
|
|||
|
||||
Build Firmware and Program Controller
|
||||
-------------------------------------
|
||||
See [doc/build.md](tmk_core/doc/build.md), or the readme in the particular keyboards/* folder.
|
||||
See [build environment setup](/readme.md#build-environment-setup), or the readme in the particular keyboards/* folder.
|
||||
|
||||
|
||||
|
||||
|
|
|
|||
|
|
@ -2,7 +2,7 @@ Keycode Symbol Table
|
|||
====================
|
||||
Keycodes are defined in `common/keycode.h`.
|
||||
Range of 00-A4 and E0-E7 are identical with HID Usage:
|
||||
<http://www.usb.org/developers/devclass_docs/Hut1_11.pdf>
|
||||
<http://www.usb.org/developers/hidpage/Hut1_12v2.pdf>
|
||||
Virtual keycodes are defined out of above range to support special actions.
|
||||
|
||||
|
||||
|
|
|
|||
|
|
@ -2,11 +2,11 @@
|
|||
|
||||
ifdef TEENSY2
|
||||
OPT_DEFS += -DATREUS_TEENSY2
|
||||
ATRUES_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex
|
||||
ATREUS_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex
|
||||
else
|
||||
OPT_DEFS += -DATREUS_ASTAR
|
||||
OPT_DEFS += -DCATERINA_BOOTLOADER
|
||||
ATRUES_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \
|
||||
ATREUS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \
|
||||
avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB)
|
||||
endif
|
||||
|
||||
|
|
@ -84,5 +84,5 @@ endif
|
|||
USB ?= /dev/cu.usbmodem1411
|
||||
|
||||
upload: build
|
||||
$(ATRUES_UPLOAD_COMMAND)
|
||||
|
||||
$(ATREUS_UPLOAD_COMMAND)
|
||||
|
||||
|
|
|
|||
89
keyboards/atreus/keymaps/xyverz/keymap.c
Normal file
89
keyboards/atreus/keymaps/xyverz/keymap.c
Normal file
|
|
@ -0,0 +1,89 @@
|
|||
// This is the personal keymap of Ian Sterling (@xyverz). It is based on the keymap by
|
||||
// Chris Gerber (@gerbercj), with the addition of persistent layers like the Planck and
|
||||
// Preonic keyboards by Jack Humbert.
|
||||
|
||||
#include "atreus.h"
|
||||
#include "action_layer.h"
|
||||
#include "eeconfig.h"
|
||||
|
||||
extern keymap_config_t keymap_config;
|
||||
|
||||
// Each layer gets a name for readability, which is then used in the keymap matrix below.
|
||||
// The underscores don't mean anything - you can have a layer called STUFF or any other name.
|
||||
// Layer names don't all need to be of the same length, obviously, and you can also skip them
|
||||
// entirely and just use numbers.
|
||||
#define _DV 0
|
||||
#define _QW 1
|
||||
#define _CM 2
|
||||
#define _L1 3
|
||||
#define _L2 4
|
||||
|
||||
// Macro name shortcuts
|
||||
#define DVORAK M(_DV)
|
||||
#define QWERTY M(_QW)
|
||||
#define COLEMAK M(_CM)
|
||||
|
||||
|
||||
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
|
||||
[_DV] = { /* Dvorak */
|
||||
{KC_QUOT, KC_COMM, KC_DOT, KC_P, KC_Y, KC_NO, KC_F, KC_G, KC_C, KC_R, KC_L },
|
||||
{KC_A, KC_O, KC_E, KC_U, KC_I, KC_NO, KC_D, KC_H, KC_T, KC_N, KC_S },
|
||||
{SFT_T(KC_SCLN), KC_Q, KC_J, KC_K, KC_X, CTL_T(KC_DEL), KC_B, KC_M, KC_W, KC_V, SFT_T(KC_Z) },
|
||||
{KC_ESC, KC_TAB, KC_LGUI, MO(_L2), KC_BSPC, ALT_T(KC_ENT), KC_SPC, MO(_L1), KC_MINS, KC_SLSH, KC_EQL}
|
||||
},
|
||||
[_QW] = { /* Qwerty */
|
||||
{KC_Q, KC_W, KC_E, KC_R, KC_T, KC_NO, KC_Y, KC_U, KC_I, KC_O, KC_P },
|
||||
{KC_A, KC_S, KC_D, KC_F, KC_G, KC_NO, KC_H, KC_J, KC_K, KC_L, KC_SCLN},
|
||||
{SFT_T(KC_Z), KC_X, KC_C, KC_V, KC_B, CTL_T(KC_DEL), KC_N, KC_M, KC_COMM, KC_DOT, SFT_T(KC_SLSH) },
|
||||
{KC_ESC, KC_TAB, KC_LGUI, MO(_L2), KC_BSPC, ALT_T(KC_ENT), KC_SPC, MO(_L1), KC_MINS, KC_QUOT, KC_ENT}
|
||||
},
|
||||
[_CM] = { /* Colemak */
|
||||
{KC_Q, KC_W, KC_F, KC_P, KC_G, KC_NO, KC_J, KC_L, KC_U, KC_Y, KC_SCLN},
|
||||
{KC_A, KC_R, KC_S, KC_T, KC_D, KC_NO, KC_H, KC_N, KC_E, KC_I, KC_O },
|
||||
{SFT_T(KC_Z), KC_X, KC_C, KC_V, KC_B, CTL_T(KC_DEL), KC_K, KC_M, KC_COMM, KC_DOT, SFT_T(KC_SLSH) },
|
||||
{KC_ESC, KC_TAB, KC_LGUI, MO(_L2), KC_BSPC, ALT_T(KC_ENT), KC_SPC, MO(_L1), KC_MINS, KC_QUOT, KC_ENT}
|
||||
},
|
||||
[_L1] = { /* LAYER 1 */
|
||||
{KC_1, KC_2, KC_3, KC_4, KC_5, KC_NO, KC_6, KC_7, KC_8, KC_9, KC_0 },
|
||||
{KC_TAB, KC_INS, KC_UP, KC_DEL, KC_HOME, KC_NO, KC_PGUP, KC_MUTE, KC_VOLD, KC_VOLU, KC_EQL },
|
||||
{KC_TRNS, KC_LEFT, KC_DOWN, KC_RGHT, KC_END, KC_LCTL, KC_PGDN, KC_MPRV, KC_MPLY, KC_MNXT, KC_BSLS},
|
||||
{KC_TRNS, KC_GRV, KC_LGUI, KC_TRNS, KC_DEL, KC_LALT, KC_SPC, KC_TRNS, KC_LBRC, KC_RBRC, KC_ENT }
|
||||
},
|
||||
[_L2] = { /* LAYER 2 */
|
||||
{KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_NO, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN},
|
||||
{KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_NO, KC_TRNS, KC_F6, KC_F7, KC_F8, KC_PLUS},
|
||||
{KC_TRNS, KC_TRNS, DVORAK, QWERTY, COLEMAK, KC_LCTL, KC_TRNS, KC_F9, KC_F10, KC_F11, KC_F12 },
|
||||
{KC_TRNS, KC_TRNS, KC_LGUI, KC_TRNS, KC_BSPC, KC_LALT, KC_SPC, KC_TRNS, LSFT(KC_LBRC), LSFT(KC_RBRC), RESET}
|
||||
}
|
||||
};
|
||||
|
||||
const uint16_t PROGMEM fn_actions[] = {
|
||||
|
||||
};
|
||||
|
||||
void persistant_default_layer_set(uint16_t default_layer) {
|
||||
eeconfig_update_default_layer(default_layer);
|
||||
default_layer_set(default_layer);
|
||||
}
|
||||
|
||||
const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
|
||||
{
|
||||
switch(id) {
|
||||
case _DV:
|
||||
if (record->event.pressed) {
|
||||
persistant_default_layer_set(1UL<<_DV);
|
||||
}
|
||||
break;
|
||||
case _QW:
|
||||
if (record->event.pressed) {
|
||||
persistant_default_layer_set(1UL<<_QW);
|
||||
}
|
||||
break;
|
||||
case _CM:
|
||||
if (record->event.pressed) {
|
||||
persistant_default_layer_set(1UL<<_CM);
|
||||
}
|
||||
break;
|
||||
}
|
||||
return MACRO_NONE;
|
||||
};
|
||||
|
|
@ -90,7 +90,7 @@ OPT_DEFS += -DBOOTLOADER_SIZE=4096
|
|||
|
||||
|
||||
# Build Options
|
||||
# comment out to disable the options.
|
||||
# change to no to disable the options.
|
||||
#
|
||||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
|
||||
MOUSEKEY_ENABLE ?= no # Mouse keys(+4700)
|
||||
|
|
|
|||
|
|
@ -29,9 +29,6 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|||
/* COL2ROW or ROW2COL */
|
||||
#define DIODE_DIRECTION COL2ROW
|
||||
|
||||
/* define if matrix has ghost */
|
||||
//#define MATRIX_HAS_GHOST
|
||||
|
||||
/* Set 0 if debouncing isn't needed */
|
||||
#define DEBOUNCING_DELAY 5
|
||||
|
||||
|
|
|
|||
|
|
@ -66,19 +66,11 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
|
|||
* `----------------------------------------------------------------------------------'
|
||||
*/
|
||||
[_RS] = KEYMAP(
|
||||
#ifdef RGBLIGHT_ENABLE
|
||||
KC_TRNS, KC_TRNS, KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, RGB_TOG, RGB_VAI, \
|
||||
KC_TRNS, KC_TRNS, KC_TRNS,KC_TRNS,RESET, KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, RGB_VAD, \
|
||||
KC_TRNS, KC_TRNS, MO(_RS),KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \
|
||||
MO(_FL), KC_TRNS, KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, MO(_FL), RGB_SAI, \
|
||||
KC_TRNS, KC_TRNS, KC_TRNS,KC_TRNS, RGB_MOD, RGB_MOD, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, RGB_HUD, RGB_SAD, RGB_HUI),
|
||||
#else
|
||||
KC_TRNS, KC_TRNS, KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \
|
||||
KC_TRNS, KC_TRNS, KC_TRNS,KC_TRNS,RESET, KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \
|
||||
KC_TRNS, KC_TRNS, MO(_RS),KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \
|
||||
KC_TRNS, KC_TRNS, KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \
|
||||
KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, MO(_FL), KC_TRNS, KC_TRNS, KC_TRNS),
|
||||
#endif
|
||||
};
|
||||
|
||||
enum function_id {
|
||||
|
|
|
|||
5
keyboards/clueboard/keymaps/skully/readme.md
Normal file
5
keyboards/clueboard/keymaps/skully/readme.md
Normal file
|
|
@ -0,0 +1,5 @@
|
|||
# skullY's Clueboard Layout
|
||||
|
||||
This layout is what I (@skullydazed) use on my personal Clueboards. I mostly use it for programming, CAD, and general typing.
|
||||
|
||||
The most notable change from the default layout is putting Ctrl on the Capslock key. I also swap Alt and Cmd because I mostly use a Mac day to day.
|
||||
|
|
@ -1,4 +1,97 @@
|
|||
Clueboard keyboard firmware
|
||||
======================
|
||||
|
||||
TODO: to be updated.
|
||||
DIY/Assembled compact 66% keyboard by [Clueboard](http://clueboard.co).
|
||||
|
||||
For the full Quantum Mechanical Keyboard feature list, see [the parent readme.md](/readme.md).
|
||||
|
||||
## First Time Setup
|
||||
|
||||
Download or clone the whole firmware and navigate to the keyboards/clueboard directory. Once your dev env is setup, you'll be able to generate the default .hex:
|
||||
|
||||
```
|
||||
$ make
|
||||
```
|
||||
|
||||
You will see a lot of output and if everything worked correctly you will see something similar to this:
|
||||
|
||||
```
|
||||
Size after:
|
||||
text data bss dec hex filename
|
||||
0 19992 0 19992 4e18 clueboard_rev2_default.hex
|
||||
```
|
||||
|
||||
At this point you can press RESET on your Clueboard and flash your keyboard with this command:
|
||||
|
||||
```
|
||||
$ make dfu
|
||||
```
|
||||
|
||||
If you would like to use one of the alternative keymaps, or create your own, see below.
|
||||
|
||||
## Clueboard 1.0
|
||||
|
||||
If you have a first generation Clueboard (one with a black PCB) you will need to use the revision 1 code. To do so add `SUBPROJECT=rev1` to your make command, like this:
|
||||
|
||||
```
|
||||
$ make SUBPROJECT=rev1
|
||||
```
|
||||
|
||||
And when flashing your keyboard:
|
||||
|
||||
```
|
||||
$ make SUBPROJECT=rev1 dfu
|
||||
```
|
||||
|
||||
If you are flashing an alternative layout to your rev1, include both `SUBPROJECT=rev1` and `KEYMAP=<keymap>` in your command, for example when flashing max:
|
||||
|
||||
```
|
||||
$ make SUBPROJECT=rev1 KEYMAP=max dfu
|
||||
```
|
||||
|
||||
## Alternate Keymaps
|
||||
|
||||
There are many alternative and user-contributed layouts available in the [keymaps/](keymaps/) directory. To compile and flash an alternative you will want to add `KEYMAP=<keymap>` to your command:
|
||||
|
||||
```
|
||||
$ make KEYMAP=skully
|
||||
```
|
||||
|
||||
And when flashing your keyboard, put `KEYMAP=<keymap>` between "make" and "dfu":
|
||||
|
||||
```
|
||||
$ make KEYMAP=skully dfu
|
||||
```
|
||||
|
||||
### Notable Layouts
|
||||
|
||||
These layouts are notable for one reason or another. If you are looking for ideas or inspiration you should look at these first:
|
||||
|
||||
* [keymaps/default](keymaps/default) - The default Clueboard layout
|
||||
* [keymaps/max](keymaps/max) - A maximised layout that makes use of every key and feature of the Clueboard 2.0 PCB.
|
||||
* [keymaps/skully](keymaps/skully) - The layout that @skullydazed uses on his own Clueboards.
|
||||
|
||||
## Create Your Own Keymap
|
||||
|
||||
There are a lot of possibilities when creating your own keymap, and the primary documentation for doing that is [Customizing Your Keymap](/readme.md##customizing-your-keymap) in the main readme.md. As a way to get started, here is the procedure I recommend:
|
||||
|
||||
* Copy `[keymaps/default](keymaps/default/)` to `keymaps/<your_layout>`.
|
||||
* Compile the firmware (`$ make KEYMAP=<your_layout>`)
|
||||
* Flash the firmware (`$ make KEYMAP=<your_layout> dfu`)
|
||||
* Make sure everything works like the default keyboard
|
||||
* Modify `keymaps/<your_layout>/readme.md` to tell others about your layout.
|
||||
* Modify `keymaps/<your_layout>/keymap.c` to reflect your desired layout.
|
||||
* Compile your new custom firmware (`$ make KEYMAP=<your_layout>`)
|
||||
** If you have warnings you may flash without fixing them, but something may not work right.
|
||||
** If you have any errors you must fix them before continuing.
|
||||
* Flash the firmware (`$ make KEYMAP=<your_layout> dfu`)
|
||||
|
||||
## Share Your Keymap
|
||||
|
||||
Got your layout dialed in? Please share it with the world so we can benefit from your work! Simply submit a pull request with your layout and we'll include it in the official repository. Please use the following guidelines when putting together your pull request:
|
||||
|
||||
* Include a readme.md that states what your primary keyboard use is, how your layout differs from the default, and highlights anything you think makes your layout particularly great.
|
||||
* If your layout requires certain features (EG, RGB underlight or backlighting) ensure you have a Makefile and config.h that reflects that
|
||||
* If your layout requires special hardware to be added, please describe that in the readme.md
|
||||
|
||||
TODO: Write up or link quick how-to on creating and submitting a PR. (Pull requests accepted. :)
|
||||
|
|
|
|||
|
|
@ -36,4 +36,4 @@
|
|||
#define RGBLIGHT_SAT_STEP 17
|
||||
#define RGBLIGHT_VAL_STEP 17
|
||||
|
||||
#endif
|
||||
#endif
|
||||
|
|
|
|||
|
|
@ -1,63 +0,0 @@
|
|||
#include "clueboard2.h"
|
||||
|
||||
void matrix_init_kb(void) {
|
||||
// put your keyboard start-up code here
|
||||
// runs once when the firmware starts up
|
||||
matrix_init_user();
|
||||
led_init_ports();
|
||||
|
||||
// JTAG disable for PORT F. write JTD bit twice within four cycles.
|
||||
MCUCR |= (1<<JTD);
|
||||
MCUCR |= (1<<JTD);
|
||||
};
|
||||
|
||||
void led_init_ports() {
|
||||
// * Set our LED pins as output
|
||||
DDRB |= (1<<4);
|
||||
}
|
||||
|
||||
void led_set_kb(uint8_t usb_led) {
|
||||
if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
|
||||
// Turn capslock on
|
||||
PORTB |= (1<<4);
|
||||
} else {
|
||||
// Turn capslock off
|
||||
PORTB &= ~(1<<4);
|
||||
}
|
||||
}
|
||||
|
||||
/* Clueboard 2.0 LED locations:
|
||||
*
|
||||
* Capslock: B4, pull high to turn on
|
||||
* LCtrl: Shared with Capslock, DO NOT INSTALL LED'S IN BOTH
|
||||
* Page Up: B7, pull high to turn on
|
||||
* Escape: D6, pull high to turn on
|
||||
* Arrows: D4, pull high to turn on
|
||||
*/
|
||||
|
||||
void backlight_init_ports(void) {
|
||||
print("init_backlight_pin()\n");
|
||||
// Set our LED pins as output
|
||||
DDRD |= (1<<6); // Esc
|
||||
DDRB |= (1<<7); // Page Up
|
||||
DDRD |= (1<<4); // Arrows
|
||||
|
||||
// Set our LED pins low
|
||||
PORTD &= ~(1<<6); // Esc
|
||||
PORTB &= ~(1<<7); // Page Up
|
||||
PORTD &= ~(1<<4); // Arrows
|
||||
}
|
||||
|
||||
void backlight_set(uint8_t level) {
|
||||
if ( level == 0 ) {
|
||||
// Turn off light
|
||||
PORTD |= (1<<6); // Esc
|
||||
PORTB |= (1<<7); // Page Up
|
||||
PORTD |= (1<<4); // Arrows
|
||||
} else {
|
||||
// Turn on light
|
||||
PORTD &= ~(1<<6); // Esc
|
||||
PORTB &= ~(1<<7); // Page Up
|
||||
PORTD &= ~(1<<4); // Arrows
|
||||
}
|
||||
}
|
||||
76
keyboards/cluecard/Makefile
Normal file
76
keyboards/cluecard/Makefile
Normal file
|
|
@ -0,0 +1,76 @@
|
|||
|
||||
|
||||
# MCU name
|
||||
#MCU = at90usb1287
|
||||
MCU = atmega32u4
|
||||
|
||||
# Processor frequency.
|
||||
# This will define a symbol, F_CPU, in all source code files equal to the
|
||||
# processor frequency in Hz. You can then use this symbol in your source code to
|
||||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
||||
# automatically to create a 32-bit value in your source code.
|
||||
#
|
||||
# This will be an integer division of F_USB below, as it is sourced by
|
||||
# F_USB after it has run through any CPU prescalers. Note that this value
|
||||
# does not *change* the processor frequency - it should merely be updated to
|
||||
# reflect the processor speed set externally so that the code can use accurate
|
||||
# software delays.
|
||||
F_CPU = 16000000
|
||||
|
||||
|
||||
#
|
||||
# LUFA specific
|
||||
#
|
||||
# Target architecture (see library "Board Types" documentation).
|
||||
ARCH = AVR8
|
||||
|
||||
# Input clock frequency.
|
||||
# This will define a symbol, F_USB, in all source code files equal to the
|
||||
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
||||
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
||||
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
||||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
||||
# at the end, this will be done automatically to create a 32-bit value in your
|
||||
# source code.
|
||||
#
|
||||
# If no clock division is performed on the input clock inside the AVR (via the
|
||||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
||||
F_USB = $(F_CPU)
|
||||
|
||||
# Interrupt driven control endpoint task(+60)
|
||||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
||||
|
||||
|
||||
# Boot Section Size in *bytes*
|
||||
# Teensy halfKay 512
|
||||
# Teensy++ halfKay 1024
|
||||
# Atmel DFU loader 4096
|
||||
# LUFA bootloader 4096
|
||||
# USBaspLoader 2048
|
||||
OPT_DEFS += -DBOOTLOADER_SIZE=4096
|
||||
|
||||
|
||||
# Build Options
|
||||
# change yes to no to disable
|
||||
#
|
||||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
|
||||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
|
||||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
|
||||
CONSOLE_ENABLE ?= yes # Console for debug(+400)
|
||||
COMMAND_ENABLE ?= yes # Commands for debug and configuration
|
||||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
|
||||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
|
||||
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
|
||||
NKRO_ENABLE ?= no # USB Nkey Rollover
|
||||
RGBLIGHT_ENABLE ?= yes # Enable keyboard underlight functionality (+4870)
|
||||
BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality by default
|
||||
MIDI_ENABLE ?= no # MIDI controls
|
||||
UNICODE_ENABLE ?= no # Unicode
|
||||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
|
||||
AUDIO_ENABLE ?= yes # Audio output on port C6
|
||||
|
||||
ifndef QUANTUM_DIR
|
||||
include ../../Makefile
|
||||
endif
|
||||
|
||||
|
||||
98
keyboards/cluecard/cluecard.c
Normal file
98
keyboards/cluecard/cluecard.c
Normal file
|
|
@ -0,0 +1,98 @@
|
|||
#include "cluecard.h"
|
||||
#define BL_RED OCR1B
|
||||
#define BL_GREEN OCR1A
|
||||
#define BL_BLUE OCR1C
|
||||
|
||||
void matrix_init_kb(void) {
|
||||
// put your keyboard start-up code here
|
||||
// runs once when the firmware starts up
|
||||
|
||||
matrix_init_user();
|
||||
}
|
||||
|
||||
void matrix_scan_kb(void) {
|
||||
// put your looping keyboard code here
|
||||
// runs every cycle (a lot)
|
||||
|
||||
matrix_scan_user();
|
||||
}
|
||||
|
||||
bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
|
||||
// put your per-action keyboard code here
|
||||
// runs for every action, just before processing by the firmware
|
||||
|
||||
return process_record_user(keycode, record);
|
||||
}
|
||||
|
||||
void led_set_kb(uint8_t usb_led) {
|
||||
// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
|
||||
|
||||
led_set_user(usb_led);
|
||||
}
|
||||
|
||||
void backlight_init_ports(void)
|
||||
{
|
||||
// Set B5, B6, and B7 as output
|
||||
DDRB |= (1<<7)|(1<<6)|(1<<5);
|
||||
|
||||
// Setup PWM
|
||||
ICR1 = 0xFFFF;
|
||||
TCCR1A = 0b10101010;
|
||||
TCCR1B = 0b00011001;
|
||||
|
||||
BL_RED = 0xFFFF;
|
||||
BL_GREEN = 0xFFFF;
|
||||
BL_BLUE = 0xFFFF;
|
||||
}
|
||||
|
||||
void backlight_set(uint8_t level)
|
||||
{
|
||||
// Set the RGB color
|
||||
switch (level)
|
||||
{
|
||||
case 0:
|
||||
// Off
|
||||
BL_RED = 0xFFFF;
|
||||
BL_GREEN = 0xFFFF;
|
||||
BL_BLUE = 0xFFFF;
|
||||
break;
|
||||
case 1:
|
||||
// Red
|
||||
BL_RED = 0x0000;
|
||||
BL_GREEN = 0xFFFF;
|
||||
BL_BLUE = 0xFFFF;
|
||||
break;
|
||||
case 2:
|
||||
// Green
|
||||
BL_RED = 0xFFFF;
|
||||
BL_GREEN = 0x0000;
|
||||
BL_BLUE = 0xFFFF;
|
||||
break;
|
||||
case 3:
|
||||
// Blue
|
||||
BL_RED = 0xFFFF;
|
||||
BL_GREEN = 0xFFFF;
|
||||
BL_BLUE = 0x0000;
|
||||
break;
|
||||
case 4:
|
||||
// Magenta
|
||||
BL_RED = 0x4000;
|
||||
BL_GREEN = 0x4000;
|
||||
BL_BLUE = 0x4000;
|
||||
break;
|
||||
case 5:
|
||||
// Purple
|
||||
BL_RED = 0x0000;
|
||||
BL_GREEN = 0xFFFF;
|
||||
BL_BLUE = 0x0000;
|
||||
break;
|
||||
case 6:
|
||||
// Yellow
|
||||
BL_RED = 0x0000;
|
||||
BL_GREEN = 0x0000;
|
||||
BL_BLUE = 0xFFFF;
|
||||
break;
|
||||
default:
|
||||
xprintf("Unknown level: %d\n", level);
|
||||
}
|
||||
}
|
||||
22
keyboards/cluecard/cluecard.h
Normal file
22
keyboards/cluecard/cluecard.h
Normal file
|
|
@ -0,0 +1,22 @@
|
|||
#ifndef CLUECARD_H
|
||||
#define CLUECARD_H
|
||||
|
||||
#include "quantum.h"
|
||||
|
||||
// This a shortcut to help you visually see your layout.
|
||||
// The first section contains all of the arguements
|
||||
// The second converts the arguments into a two-dimensional array
|
||||
#define KEYMAP( \
|
||||
k00, k01, k02, \
|
||||
k10, k12, \
|
||||
k20, k21, k22, \
|
||||
k11, \
|
||||
k30, k31, k32 \
|
||||
) { \
|
||||
{ k00, k01, k02, }, \
|
||||
{ k10, k11, k12, }, \
|
||||
{ k20, k21, k22, }, \
|
||||
{ k30, k31, k32, } \
|
||||
}
|
||||
|
||||
#endif
|
||||
167
keyboards/cluecard/config.h
Normal file
167
keyboards/cluecard/config.h
Normal file
|
|
@ -0,0 +1,167 @@
|
|||
/*
|
||||
Copyright 2012 Jun Wako <wakojun@gmail.com>
|
||||
|
||||
This program is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 2 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
This program is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public License
|
||||
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#ifndef CONFIG_H
|
||||
#define CONFIG_H
|
||||
|
||||
#include "config_common.h"
|
||||
|
||||
/* USB Device descriptor parameter */
|
||||
#define VENDOR_ID 0xC1ED
|
||||
#define PRODUCT_ID 0x2330
|
||||
#define DEVICE_VER 0x0001
|
||||
#define MANUFACTURER Clueboard
|
||||
#define PRODUCT ATMEGA32U4 Firmware Dev Kit
|
||||
#define DESCRIPTION A small board to help you hack on QMK.
|
||||
|
||||
/* key matrix size */
|
||||
#define MATRIX_ROWS 4
|
||||
#define MATRIX_COLS 3
|
||||
|
||||
/*
|
||||
* Keyboard Matrix Assignments
|
||||
*
|
||||
* Change this to how you wired your keyboard
|
||||
* COLS: AVR pins used for columns, left to right
|
||||
* ROWS: AVR pins used for rows, top to bottom
|
||||
* DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
|
||||
* ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
|
||||
*
|
||||
*/
|
||||
#define MATRIX_ROW_PINS { F0, F5, F4, B4 }
|
||||
#define MATRIX_COL_PINS { F1, F7, F6 }
|
||||
#define UNUSED_PINS
|
||||
|
||||
/* COL2ROW or ROW2COL */
|
||||
#define DIODE_DIRECTION ROW2COL
|
||||
|
||||
/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
|
||||
#define DEBOUNCING_DELAY 20
|
||||
|
||||
/* define if matrix has ghost (lacks anti-ghosting diodes) */
|
||||
//#define MATRIX_HAS_GHOST
|
||||
|
||||
/* number of backlight levels */
|
||||
#define BACKLIGHT_LEVELS 6
|
||||
|
||||
/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
|
||||
//#define LOCKING_SUPPORT_ENABLE
|
||||
/* Locking resynchronize hack */
|
||||
//#define LOCKING_RESYNC_ENABLE
|
||||
|
||||
/*
|
||||
* Force NKRO
|
||||
*
|
||||
* Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
|
||||
* state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
|
||||
* makefile for this to work.)
|
||||
*
|
||||
* If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
|
||||
* until the next keyboard reset.
|
||||
*
|
||||
* NKRO may prevent your keystrokes from being detected in the BIOS, but it is
|
||||
* fully operational during normal computer usage.
|
||||
*
|
||||
* For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
|
||||
* or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
|
||||
* bootmagic, NKRO mode will always be enabled until it is toggled again during a
|
||||
* power-up.
|
||||
*
|
||||
*/
|
||||
//#define FORCE_NKRO
|
||||
|
||||
/*
|
||||
* Magic Key Options
|
||||
*
|
||||
* Magic keys are hotkey commands that allow control over firmware functions of
|
||||
* the keyboard. They are best used in combination with the HID Listen program,
|
||||
* found here: https://www.pjrc.com/teensy/hid_listen.html
|
||||
*
|
||||
* The options below allow the magic key functionality to be changed. This is
|
||||
* useful if your keyboard/keypad is missing keys and you want magic key support.
|
||||
*
|
||||
*/
|
||||
|
||||
/* key combination for magic key command */
|
||||
#define IS_COMMAND() ( \
|
||||
keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
|
||||
)
|
||||
|
||||
/* control how magic key switches layers */
|
||||
//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true
|
||||
//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true
|
||||
//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
|
||||
|
||||
/* override magic key keymap */
|
||||
//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
|
||||
//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
|
||||
//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
|
||||
//#define MAGIC_KEY_HELP1 H
|
||||
//#define MAGIC_KEY_HELP2 SLASH
|
||||
//#define MAGIC_KEY_DEBUG D
|
||||
//#define MAGIC_KEY_DEBUG_MATRIX X
|
||||
//#define MAGIC_KEY_DEBUG_KBD K
|
||||
//#define MAGIC_KEY_DEBUG_MOUSE M
|
||||
//#define MAGIC_KEY_VERSION V
|
||||
//#define MAGIC_KEY_STATUS S
|
||||
//#define MAGIC_KEY_CONSOLE C
|
||||
//#define MAGIC_KEY_LAYER0_ALT1 ESC
|
||||
//#define MAGIC_KEY_LAYER0_ALT2 GRAVE
|
||||
//#define MAGIC_KEY_LAYER0 0
|
||||
//#define MAGIC_KEY_LAYER1 1
|
||||
//#define MAGIC_KEY_LAYER2 2
|
||||
//#define MAGIC_KEY_LAYER3 3
|
||||
//#define MAGIC_KEY_LAYER4 4
|
||||
//#define MAGIC_KEY_LAYER5 5
|
||||
//#define MAGIC_KEY_LAYER6 6
|
||||
//#define MAGIC_KEY_LAYER7 7
|
||||
//#define MAGIC_KEY_LAYER8 8
|
||||
//#define MAGIC_KEY_LAYER9 9
|
||||
//#define MAGIC_KEY_BOOTLOADER PAUSE
|
||||
//#define MAGIC_KEY_LOCK CAPS
|
||||
//#define MAGIC_KEY_EEPROM E
|
||||
//#define MAGIC_KEY_NKRO N
|
||||
//#define MAGIC_KEY_SLEEP_LED Z
|
||||
|
||||
/* Underlight configuration
|
||||
*/
|
||||
#define RGB_DI_PIN E6
|
||||
//#define RGBLIGHT_TIMER
|
||||
#define RGBLED_NUM 4 // Number of LEDs
|
||||
#define RGBLIGHT_HUE_STEP 10
|
||||
#define RGBLIGHT_SAT_STEP 17
|
||||
#define RGBLIGHT_VAL_STEP 17
|
||||
|
||||
/*
|
||||
* Feature disable options
|
||||
* These options are also useful to firmware size reduction.
|
||||
*/
|
||||
|
||||
/* disable debug print */
|
||||
//#define NO_DEBUG
|
||||
|
||||
/* disable print */
|
||||
//#define NO_PRINT
|
||||
|
||||
/* disable action features */
|
||||
//#define NO_ACTION_LAYER
|
||||
//#define NO_ACTION_TAPPING
|
||||
//#define NO_ACTION_ONESHOT
|
||||
//#define NO_ACTION_MACRO
|
||||
//#define NO_ACTION_FUNCTION
|
||||
|
||||
#endif
|
||||
21
keyboards/cluecard/keymaps/default/Makefile
Normal file
21
keyboards/cluecard/keymaps/default/Makefile
Normal file
|
|
@ -0,0 +1,21 @@
|
|||
# Build Options
|
||||
# change to "no" to disable the options, or define them in the Makefile in
|
||||
# the appropriate keymap folder that will get included automatically
|
||||
#
|
||||
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
|
||||
MOUSEKEY_ENABLE = no # Mouse keys(+4700)
|
||||
EXTRAKEY_ENABLE = no # Audio control and System control(+450)
|
||||
CONSOLE_ENABLE = yes # Console for debug(+400)
|
||||
COMMAND_ENABLE = yes # Commands for debug and configuration
|
||||
NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
|
||||
BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
|
||||
MIDI_ENABLE = no # MIDI controls
|
||||
AUDIO_ENABLE = yes # Audio output on port C6
|
||||
UNICODE_ENABLE = no # Unicode
|
||||
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
|
||||
RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight.
|
||||
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
|
||||
|
||||
ifndef QUANTUM_DIR
|
||||
include ../../../../Makefile
|
||||
endif
|
||||
8
keyboards/cluecard/keymaps/default/config.h
Normal file
8
keyboards/cluecard/keymaps/default/config.h
Normal file
|
|
@ -0,0 +1,8 @@
|
|||
#ifndef CONFIG_USER_H
|
||||
#define CONFIG_USER_H
|
||||
|
||||
#include "../../config.h"
|
||||
|
||||
// place overrides here
|
||||
|
||||
#endif
|
||||
63
keyboards/cluecard/keymaps/default/keymap.c
Normal file
63
keyboards/cluecard/keymaps/default/keymap.c
Normal file
|
|
@ -0,0 +1,63 @@
|
|||
#include "cluecard.h"
|
||||
#ifdef AUDIO_ENABLE
|
||||
#include "audio.h"
|
||||
#endif
|
||||
|
||||
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
|
||||
[0] = KEYMAP(
|
||||
RGB_TOG, RGB_SAI, RGB_VAI, \
|
||||
RGB_HUD, RGB_HUI, \
|
||||
RGB_MOD, RGB_SAD, RGB_VAD, \
|
||||
BL_STEP, \
|
||||
F(0), F(1), F(2) \
|
||||
)
|
||||
};
|
||||
|
||||
#ifdef AUDIO_ENABLE
|
||||
|
||||
float tone_startup[][2] = SONG(STARTUP_SOUND);
|
||||
float tone_qwerty[][2] = SONG(QWERTY_SOUND);
|
||||
float tone_dvorak[][2] = SONG(DVORAK_SOUND);
|
||||
float tone_colemak[][2] = SONG(COLEMAK_SOUND);
|
||||
float tone_plover[][2] = SONG(PLOVER_SOUND);
|
||||
float tone_plover_gb[][2] = SONG(PLOVER_GOODBYE_SOUND);
|
||||
float music_scale[][2] = SONG(MUSIC_SCALE_SOUND);
|
||||
|
||||
float tone_goodbye[][2] = SONG(GOODBYE_SOUND);
|
||||
#endif
|
||||
|
||||
const uint16_t PROGMEM fn_actions[] = {
|
||||
[0] = ACTION_FUNCTION(0),
|
||||
[1] = ACTION_FUNCTION(1),
|
||||
[2] = ACTION_FUNCTION(2)
|
||||
};
|
||||
|
||||
void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) {
|
||||
if (record->event.pressed) {
|
||||
switch (id) {
|
||||
case 0:
|
||||
PLAY_NOTE_ARRAY(tone_startup, false, 0);
|
||||
break;
|
||||
case 1:
|
||||
PLAY_NOTE_ARRAY(music_scale, false, 0);
|
||||
break;
|
||||
case 2:
|
||||
PLAY_NOTE_ARRAY(tone_goodbye, false, 0);
|
||||
break;
|
||||
}
|
||||
}
|
||||
};
|
||||
|
||||
void matrix_init_user(void) {
|
||||
}
|
||||
|
||||
void matrix_scan_user(void) {
|
||||
|
||||
}
|
||||
|
||||
bool process_record_user(uint16_t keycode, keyrecord_t *record) {
|
||||
return true;
|
||||
}
|
||||
|
||||
void led_set_user(uint8_t usb_led) {
|
||||
}
|
||||
1
keyboards/cluecard/keymaps/default/readme.md
Normal file
1
keyboards/cluecard/keymaps/default/readme.md
Normal file
|
|
@ -0,0 +1 @@
|
|||
# The default keymap for cluecard
|
||||
Some files were not shown because too many files have changed in this diff Show more
Loading…
Reference in a new issue